R & E Custom Touch Up/Spray Paint, Choose Your Paint Code for FORD. Choose your Kit: Our Touch Up kit is made for smaller scratch areas and our Aerosol cans are meant for larger areas. Cant find your paint code?
Unfortunately, we are not able to list every color but if you know your paint code we should be able to make it for you. 0.5 oz Bottle of Gray Primer. 0.5 oz bottle of Base Coat Paint. 0.5 oz bottle of Clear Coat. Each bottle includes a small brush on the inside of the lid.
Base and Clear Spraycan Kit Contains. 11 oz Aerosol can of Base Coat Paint. Comes standard with 2 nozzles (1 Fan Pattern Spray Nozzle and 1 Round Pattern Fine Atomizing Nozzle).
12 oz Aerosol can of SprayMax 3680061 2K Glamour Clear Coat. Primer, Base and Clear Spraycan Kit Contains. 13 oz Aerosol can of SprayMax 3680033, 2K Gray Epoxy Primer. R & E Custom Aerosols are pre-loaded with the color of your choice in 1K Urethane Basecoat.
Each Aerosol comes with a wide fan (white) spray nozzle tip and a fine atomizing (red) nozzle tip giving you the ability to cover more area quicker and to achieve metallic control all from one can. Salesman Note: A Clear-Coat is Required for the correct gloss, sheen, and Exterior Durability. It is Highly Recommended that you use the clear-coat included in the kit for ultra U. If you have exposed bare metal you will need the kit that includes the Epoxy Primer.
Primer will be required prior to applying the color coat if you have exposed bare metal. Allow to dry for a minimum of 2 hours before applying sandable primer (if required) or the color coat. If you have exposed body filler or minor imperfections such as scratches, scrapes, and scuff marks, use SprayMax 3680031 Rapid Primer Filler for a sandable surface.Once cured over night, wet or dry sand the surface using 600-800 grit before applying the color coat. Wash thoroughly with soap and hot water.
Clean using SprayMax 3680094 Wax & Grease Remover or equivalent. Sand using 400-600 grit wet/dry sandpaper.
Re-Clean using SprayMax 3680094 Wax & Grease Remover or equivalent. Shake can for at least 1 minute after the can begins to rattle.
Continue to shake occasionally during spray application. Hold container approximately 8-10 inches from surface being sprayed. Apply 2-3 coats or until color coverage is acheived. Note: Some colors may require more coats. Slightly Overlap each pass for uniform coverage.
Use the red tip for fine atomization, or the wide fan for quicker coverage on larger areas. Allow 5-10 minutes dry time between each coat before spraying the next coat. After color coverage is achieved allow the last coat to dry a minimum of 1 hour but not longer than 16 hours before applying a clear coat.
After each use, invert can and spray for four seconds to clear and clean the valve. If button becomes clogged, pull off and clean with solvent. Stick pins or wire into can opening.
To achieve an optimum color match, spray 3 test panels with the base-coat until complete color coverage is achieved. Next spray 1 test panel with 1 coat of mid-coat, the second test panel with 2 coats of mid-coat and the third test panel with 3 coats of mid-coat. Clear-Coat all 3 test panels and check the color match once the clear-coat has fully dried. Duplicate the same technique on your vehicle that coordinates with the test panel that best matches your vehicle. The item "R & E Custom Touch Up/Spray Paint, Choose Your Paint Code for FORD" is in sale since Wednesday, September 16, 2020.
This item is in the category "eBay Motors\Automotive Tools & Supplies\Auto Paints & Supplies\Touchup & Spray Paint". The seller is "repaintsupply" and is located in Mountain Home, Arkansas. This item can be shipped to United States.